ISP (4) | Special files and drivers | Unix Manual Pages

Alphabetical Categories About us

ISP (4) | Special files and drivers | Unix Manual Pages | :man▋

SCSI features include support for Ultra SCSI and wide mode transactions for SCSI, Ultra2 LVD (for the ISP1080 and ISP1280), and Ultra3 LVD (for the ISP12160).

Fibre Channel support uses FCP SCSI profile for FibreChannel. and utilizes Class 3 and Class 2 connections (Qlogic 2100 is Class 3 only, minor patches to the Qlogic 2200 to force Class 2 mode). Support is available for Public and Private loops, and for point-to-point connections (Qlogic 2200 only). The newer 2-Gigabit cards (2300, 2312) are also supported. Command tagging is supported for all (in fact, FibreChannel requires tagging). Fabric support is enabled by default (but may be contingent upon the correct firmware being loaded).

FIRMWARE

Firmware is now available if the ispfw(4) module is loaded during bootstrap (q.v.).

It is very strongly recommended that you use the firmware available from ispfw(4) as it is the most likely to have been tested with this driver.

HARDWARE

Cards supported by the isp driver include:

ISP1000
	SBus Fast Wide, Ultra Fast Wide cards, Single Ended or Differential cards.
PTI SBS440
	Performance Technology ISP1000 variants.
ISP1020
	Qlogic 1020 Fast Wide and Differential Fast Wide PCI cards.
ISP1040
	Qlogic 1040 Ultra Wide and Differential Ultra Wide PCI cards. Also known as the DEC KZPBA-CA (single ended) and KZPBA-CB (HVD differential).
PTI SBS450
	Performance Technology ISP1040 variants.
Qlogic 1240
	Qlogic 1240 Dual Bus Ultra Wide and Differential Ultra Wide PCI cards.
Qlogic 1020
	Qlogic 1020 SCSI cards.
Qlogic 1040
	Qlogic 1040 Ultra SCSI cards.
Qlogic 1080
	Qlogic 1280 LVD Ultra2 Wide PCI cards.
Qlogic 1280
	Qlogic 1280 Dual Bus LVD Ultra2 Wide PCI cards.
Qlogic 12160
	Qlogic 12160 Dual Bus LVD Ultra3 Wide PCI cards.
Qlogic 2100
	Qlogic 2100 and 2100A Copper and Optical Fibre Channel Arbitrated Loop
Qlogic 2102
	Qlogic Dual Loop 2100A Optical Fibre Channel Arbitrated Loop PCI cards.
Qlogic 2200
	Qlogic 2200 Copper and Optical Fibre Channel Arbitrated Loop PCI cards.
Qlogic 2202
	Qlogic 2200 Dual Bus Optical Fibre Channel Arbitrated Loop PCI cards.
Qlogic 2204
	Qlogic 2200 Dual Bus Optical Fibre Channel Arbitrated Loop PCI cards.
Qlogic 2300
	Qlogic 2300 Optical Fibre Channel PCI cards.
Qlogic 2312
	Qlogic 2312 Optical Fibre Channel PCI cards.
PTI SBS470
	Performance Technology ISP2100 variants.
Antares P-0033
	Antares Microsystems ISP2100 variants.

CONFIGURATION OPTIONS

Target mode support may be enabled with the

.Cd options ISP_TARGET_MODE

option.

BOOT OPTIONS

The following options are switchable by setting values in the loader configuration file (see the loader(8) manual page). They are:

isp_disable	A bit mask of units to skip configuration for.
isp_mem_map	A bit mask of units to use PCI Memory space instead of I/O space access for.
isp_io_map	A bit mask of units to use PCI I/O space instead of Memory space access for.
isp_no_nvram	A bit mask of units that you wish to ignore board NVRAM settings for.
isp_nvram	A bit mask of units that you wish to specifically use board NVRAM settings for.
isp_fcduplex	A bit mask of units that you wish to specifically to set into full duplex mode.
isp_no_fcduplex
	A bit mask of units that you wish to specifically to not set into full duplex mode.
isp_wwn	This should be the full 64 bit World Wide Node Name you would like to use, overriding the value in NVRAM for the card.
isp_debug	This is a driver debug level- meaningful from 0 through 7.
isp_tdebug	This is a driver target mode debug level- meaningful from 0 through 5.

AUTHORS

BUGS

Created by Blin Media, 2008-2013

NAME

CONTENTS

SYNOPSIS