mlx%d: controller initialisation in progress...
mlx%d: initialisation complete |
| | The controller firmware is performing/has completed initialisation. |
| mlx%d: physical drive %d:%d not responding | The drive at channel:target is not responding; it may have failed or been removed. |
| mlx%d: spinning up drives... | Drive startup is in progress; this may take several minutes. |
| mlx%d: configuration checksum error | The array configuration has become corrupted. |
mlx%d: mirror race recovery in progress
mlx%d: mirror race on a critical system drive
mlx%d: mirror race recovery failed |
| | These error codes are undocumented. |
| mlx%d: physical drive %d:%d COD mismatch | Configuration data on the drive at channel:target does not match the rest of the array. |
| mlx%d: system drive installation aborted | Errors occurred preventing one or more system drives from being configured. |
| mlx%d: new controller configuration found | The controller has detected a configuration on disk which supersedes the configuration in its nonvolatile memory. It will reset and come up with the new configuration. |
| mlx%d: FATAL MEMORY PARITY ERROR | Firmware detected a fatal memory error; the driver will not attempt to attach to this controller. |
| mlx%d: unknown firmware initialisation error %x:%x:%x | An unknown error occurred during initialisation; it will be ignored. |
|
mlx%d: can’t allocate scatter/gather DMA tag
mlx%d: can’t allocate buffer DMA tag
mlx%d: can’t allocate s/g table
mlx%d: can’t make initial s/g list mapping
mlx%d: can’t make permanent s/g list mapping
mlx%d: can’t allocate interrupt
mlx%d: can’t set up interrupt |
| | A resource allocation error occurred while initialising the driver; initialisation has failed and the driver will not attach to this controller. |
| mlx%d: error fetching drive status | The current status of all system drives could not be fetched; attachment of system drives will be aborted. |
mlx%d: device_add_child failed
mlx%d: bus_generic_attach returned %d |
| | Creation of the system drive instances failed; attachment of one or more system drives may have been aborted. |
| mlxd%d: detaching... | The indicated system drive is being detached. |
| mlxd%d: still open, can’t detach | The indicated system drive is still open or mounted; the controller cannot be detached. |
| mlx%d: flushing cache... | The controller cache is being flushed prior to detach or shutdown. |
|
mlx%d: ENQUIRY failed - %s
mlx%d: ENQUIRY2 failed
mlx%d: ENQUIRY_OLD failed
mlx%d: FLUSH failed - %s
mlx%d: CHECK ASYNC failed - %s
mlx%d: REBUILD ASYNC failed - %s
mlx%d: command failed - %s |
| | The controller rejected a command for the reason given. |
mlx%d: I/O beyond end of unit (%u,%d > %u)
mlx%d: I/O error - %s |
| | An I/O error was reported by the controller. |
| mlx%d: periodic enquiry failed - %s | An attempt to poll the controller for status failed for the reason given. |
| mlx%d: mlx_periodic_enquiry: unknown command %x | The periodic status poll has issued a command which has become corrupted. |
mlxd%d: drive offline
mlxd%d: drive online
mlxd%d: drive critical |
| | The system disk indicated has changed state. |
mlx%d: physical drive %d:%d reset
mlx%d: physical drive %d:%d killed %s
"mlx%d: physical drive %d:%d error log: sense = %d asc = %x asq = %x"
"mlx%d: info %4D csi %4D" |
| | The drive at channel:target has been reset, killed for the given reason, or experienced a SCSI error. |
mlx%d: unknown log message type %x
mlx%d: error reading message log - %s |
| | An error occurred while trying to read the controller’s message log. |
mlxd%d: consistency check started
mlx%d: consistency check completed |
| | A user-initiated consistency check has started/completed. |
mlx%d: drive rebuild started for %d:%d
mlx%d: drive rebuild completed |
| | A user-initiated physical drive rebuild has started/completed. |
mlx%d: background check/rebuild operation started
mlx%d: background check/rebuild operation completed |
| | An automatic system drive consistency check or physical drive rebuild has started/completed. |
mlx%d: channel %d pausing for %d seconds
mlx%d: channel %d resuming
mlx%d: pause command failed - %s
mlx%d: pause failed for channel %d
mlx%d: resume command failed - %s
mlx%d: resume failed for channel %d |
| | Controller/channel pause operation notification. (Channel pause is not currently supported on any controller.) |
| mlx%d: controller wedged (not taking commands) | The controller is not responding to attempts to submit new commands. |
mlx%d: duplicate done event for slot %d
mlx%d: done event for nonbusy slot %d |
| | Corruption has occurred in either the controller’s onboard list of commands or in the driver. |
|
