These hooks stack the ng_ccatm node on top of a UNI stack. The node expects the interface on these hooks to conform to the upper interface specified in ng_uni(4). These hooks are forced into queuing mode, so that there are no circular calls from call control to UNI and UNI back to call control. The NNN in the hook name is the decimal port number and should not be zero. The port number is a 32-bit unsigned integer.
manage
This hook should be connected to the ILMI daemon. No data is ever sent on this hook and all received data is discarded. The hook is used to send control messages along.
dump
On receipt of a NGM_CCATM_DUMP command a textual description of the current state of the node is sent out of this hook. This text is sent as one large message consisting of more than one .Vt mbuf .
All other hook names are taken to be user hooks and correspond to an ATM endpoint as specified in the ATM Forum document. The interface on these hooks is defined in .In atmapi.h and uses a structure
struct ccatm_op {
u_int32_t op;/* request code */
u_chardata[]; /* optional data */
};
This structure is followed directly by the data for the operation. The opcode is one of the following:
enum atmop {
ATMOP_RESP,
ATMOP_ABORT_CONNECTION,
ATMOP_ACCEPT_INCOMING_CALL,
ATMOP_ADD_PARTY,
ATMOP_ADD_PARTY_REJECT,
ATMOP_ADD_PARTY_SUCCESS,
ATMOP_ARRIVAL_OF_INCOMING_CALL,
ATMOP_CALL_RELEASE,
ATMOP_CONNECT_OUTGOING_CALL,
ATMOP_DROP_PARTY,
ATMOP_GET_LOCAL_PORT_INFO,
ATMOP_P2MP_CALL_ACTIVE,
ATMOP_P2P_CALL_ACTIVE,
ATMOP_PREPARE_INCOMING_CALL,
ATMOP_PREPARE_OUTGOING_CALL,
ATMOP_QUERY_CONNECTION_ATTRIBUTES,
ATMOP_REJECT_INCOMING_CALL,
ATMOP_SET_CONNECTION_ATTRIBUTES,
ATMOP_WAIT_ON_INCOMING_CALL,
ATMOP_SET_CONNECTION_ATTRIBUTES_X,
ATMOP_QUERY_CONNECTION_ATTRIBUTES_X,
ATMOP_QUERY_STATE
};
These codes correspond directly to the operations specified in the ATM Forum document with the following exceptions:
ATMOP_RESP
As discussed in ng_uni(4), this is used to "synchronify" the interface. The argument is a
struct atm_resp {
int32_t resp;
uint32_t data; /* type of attached data */
};
If the response code resp is zero, the node has accepted the user request. If something goes wrong, resp contains an error code. For requests that return data, data contains a code describing the type of data and the data itself starts immediately after the structure.
ATMOP_QUERY_CONNECTION_ATTRIBUTES_X
This is the same as ATMOP_QUERY_CONNECTION_ATTRIBUTES except that it allows to query several attributes within one request.
ATMOP_SET_CONNECTION_ATTRIBUTES_X
This is the same as ATMOP_SET_CONNECTION_ATTRIBUTES except that it allows to set several attributes within one request. The list of attributes is followed directly by the attributes in the same order as they appear in the list.
If a user hook is disconnected, an active connection on that hook is released. Incoming connections waiting to be accepted are reoffered to other listening hooks or rejected.
This causes the internal state of the node to be dumped in ASCII to the dump hook.
NGM_CCATM_STOP
This message causes all connections on that port to be aborted (not released!) and all ATM endpoints which are bound to that port to be closed. It stops processing of all messages from the UNI stack on that port UNI stack. The argument is a
struct ngm_ccatm_port {
uint32_t port;
};
NGM_CCATM_START
Start processing on the port. The argument is a .Vt ngm_ccatm_port structure.
NGM_CCATM_CLEAR
This message takes a .Vt ngm_ccatm_port structure and clears all prefixes and addresses on that port. If the port number is zero, all ports are cleared.
NGM_CCATM_GET_ADDRESSES
Get the list of all registered addresses on the given port. The argument is a .Vt ngm_ccatm_port structure and the result is a .Vt ngm_ccatm_get_addresses structure:
struct ngm_ccatm_get_addresses {
uint32_t count;
struct ngm_ccatm_address_req addr[0];
};
struct ngm_ccatm_address_req {
u_int32_t port;
struct uni_addr addr;
};
If the port field is zero in the request, all addresses on all ports are returned. If it is not zero, only the addresses on that port are reported. The number of addresses is returned in the count field.
NGM_CCATM_ADDRESS_REGISTERED
This message is used by ILMI to inform the ng_ccatm node that a previous address registration request was successful. This causes the node to activate that address. The argument to the message is a .Vt ngm_ccatm_address_req structure.
NGM_CCATM_ADDRESS_UNREGISTERED
This message is used by ILMI to inform the ng_ccatm node that an address has been unregistered. The node clears that address from its tables. The argument is a .Vt ngm_ccatm_address_req structure.
NGM_CCATM_SET_PORT_PARAM
This request sets the parameters on the given port. The argument is a
struct ngm_ccatm_atm_port {
uint32_t port;/* port for which to set parameters */
uint32_t pcr; /* port peak cell rate */
uint32_t max_vpi_bits;
uint32_t max_vci_bits;
uint32_t max_svpc_vpi;
uint32_t max_svcc_vpi;
uint32_t min_svcc_vci;
uint8_t esi[6];
uint32_t num_addr;
};
This should be used only by ILMI and when that port is stopped and the address and prefix tables of that port are empty. The num_addr field is ignored.
NGM_CCATM_GET_PORT_PARAM
Retrieve the parameters of the given port. The argument is a .Vt ngm_ccatm_port and the result a .Vt ngm_ccatm_atm_port .
NGM_CCATM_GET_PORTLIST
Get a list of all available ports on that node. This is returned as a
struct ngm_ccatm_portlist {
uint32_t nports;
uint32_t ports[];
};
NGM_CCATM_GETSTATE
Return the state of a port. The argument is a .Vt "struct ngm_ccatm_port" and the return values as a .Vt uint32_t .
NGM_CCATM_SETLOG
This requests sets a new logging level and returns the previous one. The argument is either a .Vt uint32_t in which case it specifies the new logging level, or may be empty in which case just the old level is returned as a .Vt uint32_t .
NGM_CCATM_RESET
Reset the node. This is allowed only if the number of user hooks and connected UNI stacks is zero.
