The following argument is interpreted as an interactive format command and is added to the list of commands to be executed on the specified host(s). Multiple -c options may be given.
-i
Force ntpq to operate in interactive mode. Prompts will be written to the standard output and commands read from the standard input.
-n
Output all host addresses in dotted-quad numeric format rather than converting to the canonical host names.
-p
Print a list of the peers known to the server as well as a summary of their state. This is equivalent to the peers interactive command.
Specifying a command line option other than -i or -n will cause the specified query (queries) to be sent to the indicated host(s) immediately. Otherwise, ntpq will attempt to read interactive format commands from the standard input.
A ‘?’ by itself will print a list of all the command keywords known to this incarnation of ntpq. A ‘?’ followed by a command keyword will print function and usage information about the command. This command is probably a better source of information about ntpq than this manual page.
variable_name [= value ...]
rmvars variable_name ... clearvars
The data carried by NTP mode 6 messages consists of a list of items of the form ‘variable_name=value’, where the ‘=value’ is ignored, and can be omitted, in requests to the server to read variables. The ntpq utility maintains an internal list in which data to be included in control messages can be assembled, and sent using the readlist and writelist commands described below. The addvars command allows variables and their optional values to be added to the list. If more than one variable is to be added, the list should be comma-separated and not contain white space. The rmvars command can be used to remove individual variables from the list, while the clearlist command removes all variables from the list.
authenticate yes | no
Normally ntpq does not authenticate requests unless they are write requests. The command ‘authenticate yes’ causes ntpq to send authentication with all requests it makes. Authenticated requests causes some servers to handle requests slightly differently, and can occasionally melt the CPU in fuzzballs if you turn authentication on before doing a peer display.
cooked
Causes output from query commands to be "cooked", so that variables which are recognized by ntpq will have their values reformatted for human consumption. Variables which ntpq thinks should have a decodable value but did not are marked with a trailing ‘?’.
more | less | off
Turns internal query program debugging on and off.
delay milliseconds
Specify a time interval to be added to timestamps included in requests which require authentication. This is used to enable (unreliable) server reconfiguration over long delay network paths or between machines whose clocks are unsynchronized. Actually the server does not now require timestamps in authenticated requests, so this command may be obsolete.
host hostname
Set the host to which future queries will be sent. Hostname may be either a host name or a numeric address.
hostnames yes | no
If yes is specified, host names are printed in information displays. If no is specified, numeric addresses are printed instead. The default is yes, unless modified using the command line -n switch.
keyid keyid
This command allows the specification of a key number to be used to authenticate configuration requests. This must correspond to a key number the server has been configured to use for this purpose.
1 | 2 | 3 | 4
Sets the NTP version number which ntpq claims in packets. Defaults to 3, Note that mode 6 control messages (and modes, for that matter) did not exist in NTP version 1. There appear to be no servers left which demand version 1.
quit
Exit ntpq.
passwd
This command prompts you to type in a password (which will not be echoed) which will be used to authenticate configuration requests. The password must correspond to the key configured for use by the NTP server for this purpose if such requests are to be successful.
raw
Causes all output from query commands is printed as received from the remote server. The only formating/interpretation done on the data is to transform nonascii data into a printable (but barely understandable) form.
timeout milliseconds
Specify a timeout period for responses to server queries. The default is about 5000 milliseconds. Note that since ntpq retries each query once after a timeout, the total waiting time for a timeout will be twice the timeout value set.
Obtains and prints a list of association identifiers and peer statuses for in-spec peers of the server being queried. The list is printed in columns. The first of these is an index numbering the associations from 1 for internal use, the second the actual association identifier returned by the server and the third the status word for the peer. This is followed by a number of columns containing data decoded from the status word. See the peers command for a decode of the 'condition' field. Note that the data returned by the associations command is cached internally in ntpq. The index is then of use when dealing with stupid servers which use association identifiers which are hard for humans to type, in that for any subsequent commands which require an association identifier as an argument, the form of index may be used as an alternative.
[ variable_name [= value ...] ] ...
[ variable_name [= value ...] ] ...
Requests that a list of the server’s clock variables be sent. Servers which have a radio clock or other external synchronization will respond positively to this. If the association identifier is omitted or zero the request is for the variables of the 'system clock' and will generally get a positive response from all servers with a clock. If the server treats clocks as pseudo-peers, and hence can possibly have more than one clock connected at once, referencing the appropriate peer association ID will show the variables of a particular clock. Omitting the variable list will cause the server to return a default variable display.
lassociations
Obtains and prints a list of association identifiers and peer statuses for all associations for which the server is maintaining state. This command differs from the associations command only for servers which retain state for out-of-spec client associations (i.e., fuzzballs). Such associations are normally omitted from the display when the associations command is used, but are included in the output of lassociations.
lpassociations
Print data for all associations, including out-of-spec client associations, from the internally cached list of associations. This command differs from passociations only when dealing with fuzzballs.
lpeers
Like R peers, except a summary of all associations for which the server is maintaining state is printed. This can produce a much longer list of peers from fuzzball servers.
mreadlist assocID assocID mrl assocID assocID
Like the readlist command, except the query is done for each of a range of (nonzero) association IDs. This range is determined from the association list cached by the most recent associations command.
[ variable_name [= value ...] ]
[ variable_name [= value ...] ]
Like the readvar command, except the query is done for each of a range of (nonzero) association IDs. This range is determined from the association list cached by the most recent associations command.
opeers
An old form of the peers command with the reference ID replaced by the local interface address.
passociations
Displays association data concerning in-spec peers from the internally cached list of associations. This command performs identically to the associations except that it displays the internally stored data rather than making a new query.
peers
Obtains a current list peers of the server, along with a summary of each peer’s state. Summary information includes the address of the remote peer, the reference ID (0.0.0.0 if this is unknown), the stratum of the remote peer, the type of the peer (local, unicast, multicast or broadcast), when the last packet was received, the polling interval, in seconds, the reachability register, in octal, and the current estimated delay, offset and dispersion of the peer, all in milliseconds. The character in the left margin indicates the fate of this peer in the clock selection process. Following is a list of these characters, the pigeon used in the rv command, and a short explanation of the condition revealed.
space
(reject) The peer is discarded as unreachable, synchronized to this server (synch loop) or outrageous synchronization distance.
x
(falsetick) The peer is discarded by the intersection algorithm as a falseticker.
.
(excess) The peer is discarded as not among the first ten peers sorted by synchronization distance and so is probably a poor candidate for further consideration.
-
(outlyer) The peer is discarded by the clustering algorithm as an outlyer.
+
(candidate) The peer is a survivor and a candidate for the combining algorithm.
#
(selected) The peer is a survivor, but not among the first six peers sorted by synchronization distance. If the association is ephemeral, it may be demobilized to conserve resources.
*
(peer) The peer has been declared the system peer and lends its variables to the system variables.
o
((pps.peer)) The peer has been declared the system peer and lends its variables to the system variables. However, the actual system synchronization is derived from a pulse-per-second (PPS) signal, either indirectly via the PPS reference clock driver or directly via kernel interface.
The flash variable is a valuable debugging aid. It displays the results of the original sanity checks defined in the NTP specification RFC-1305 and additional ones added in NTP Version 4. There are eleven tests called TEST1 through TEST11. The tests are performed in a certain order designed to gain maximum diagnostic information while protecting against accidental or malicious errors. The flash variable is first initialized to zero. If after each set of tests one or more bits are set, the packet is discarded.
Tests TEST4 and TEST5 check the access permissions and cryptographic message digest. If any bits are set after that, the packet is discarded. Tests TEST10 and TEST11 check the authentication state using Autokey public-key cryptography, as described in the Authentication Options section of ntp.conf(5). If any bits are set and the association has previously been marked reachable, the packet is discarded; otherwise, the originate and receive timestamps are saved, as required by the NTP protocol, and processing continues.
Tests TEST1 through TEST3 check the packet timestamps from which the offset and delay are calculated. If any bits are set, the packet is discarded; otherwise, the packet header variables are saved. Tests TEST6 through TEST8 check the health of the server. If any bits are set, the packet is discarded; otherwise, the offset and delay relative to the server are calculated and saved. Test TEST9 checks the health of the association itself. If any bits are set, the packet is discarded; otherwise, the saved variables are passed to the clock filter and mitigation algorithms.
The flash bits for each test read in increasing order from the least significant bit are defined as follows.
TEST1
Duplicate packet. The packet is at best a casual retransmission and at worst a malicious replay.
TEST2
Bogus packet. The packet is not a reply to a message previously sent. This can happen when the NTP daemon is restarted and before somebody else notices.
TEST3
Unsynchronized. One or more timestamp fields are invalid. This normally happens when the first packet from a peer is received.
TEST4
Access is denied. See the ""Access Control"" page.
TEST5
Cryptographic authentication fails. See the Authentication Options section of ntp.conf(5).
TEST6
The server is unsynchronized. Wind up its clock first.
TEST7
The server stratum is at the maximum than 15. It is probably unsynchronized and its clock needs to be wound up.
TEST8
Either the root delay or dispersion is greater than one second, which is highly unlikely unless the peer is synchronized to Mars.
TEST9
Either the peer delay or dispersion is greater than one second, which is highly unlikely unless the peer is on Mars.
TEST10
The autokey protocol has detected an authentication failure. See the Authentication Options section of ntp.conf(5).
TEST11
The autokey protocol has not verified the server or peer is authentic and has valid public key credentials. See the Authentication Options section of ntp.conf(5).
Additional system variables used by the NTP Version 4 Autokey support include the following:
certificate filestamp
Shows the NTP seconds when the certificate file was created.
hostname host
Shows the name of the host as returned by the Unix gethostname(3) library function.
flags hex
Shows the current flag bits, where the hex bits are interpreted as follows:
0x01
autokey enabled
0x02
RSA public/private key files present
0x04
PKI certificate file present
0x08
Diffie-Hellman parameters file present
0x10
NIST leapseconds table file present
leapseconds filestamp
Shows the NTP seconds when the NIST leapseconds table file was created.
params filestamp
Shows the NTP seconds when the Diffie-Hellman agreement parameter file was created.
publickey filestamp
Shows the NTP seconds when the RSA public/private key files were created.
refresh filestamp
Shows the NTP seconds when the public cryptographic values were refreshed and signed.
tai offset
Shows the TAI-UTC offset in seconds obtained from the NIST leapseconds table.
Additional peer variables used by the NTP Version 4 Autokey support include the following:
certificate filestamp
Shows the NTP seconds when the certificate file was created.
flags hex
Shows the current flag bits, where the hex bits are interpreted as in the system variable of the same name. The bits are set in the first autokey message received from the server and then reset as the associated data are obtained from the server and stored.
hcookie hex
Shows the host cookie used in the key agreement algorithm.
initkey key
Shows the initial key used by the key list generator in the autokey protocol.
initsequence index
Shows the initial index used by the key list generator in the autokey protocol.
pcookie hex
Specifies the peer cookie used in the key agreement algorithm.
timestamp time
Shows the NTP seconds when the last autokey key list was generated and signed.
pstatus assocID
Sends a read status request to the server for the given association. The names and values of the peer variables returned will be printed. Note that the status word from the header is displayed preceding the variables, both in hexadecimal and in pidgeon English.
readlist assocID rl assocID
Requests that the values of the variables in the internal variable list be returned by the server. If the association ID is omitted or is 0 the variables are assumed to be system variables. Otherwise they are treated as peer variables. If the internal variable list is empty a request is sent without data, which should induce the remote server to return a default display.
variable_name [= value] ...
variable_name [= value] ...
Requests that the values of the specified variables be returned by the server by sending a read variables request. If the association ID is omitted or is given as zero the variables are system variables, otherwise they are peer variables and the values returned will be those of the corresponding peer. Omitting the variable list will send a request with no data which should induce the server to return a default display.
variable_name [= value] ...
Like the readvar request, except the specified variables are written instead of read.
writelist [assocID]
Like the readlist request, except the internal list variables are written instead of read.
