(num) The maximum time allowed between sending unsolicited multicast router advertisements (unit: seconds). The default value is 600. Its value must be no less than 4 seconds and no greater than 1800 seconds.
mininterval
(num) The minimum time allowed between sending unsolicited multicast router advertisements (unit: seconds). The default value is the one third of value of maxinterval. Its value must be no less than 3 seconds and no greater than .75 * the value of maxinterval.
The following items are for ICMPv6 router advertisement message header. These items can be omitted, then rtadvd will use the default values.
chlim
(num) The value for Cur Hop Limit field. The default value is 64.
raflags
(str or num) A 8-bit flags field in router advertisement message header. This field can be specified either as a case-sensitive string or as an integer. A sting consists of characters each of which corresponds to a particular flag bit(s). An integer should be the logical OR of all enabled bits. Bit 7 ( ’m’ or 0x80 ) means Managed address configuration flag bit, and Bit 6 ( ’o’ or 0x40 ) means Other stateful configuration flag bit. Bit 4 ( 0x10 ) and Bit 3 ( 0x08 ) are used to encode router preference. Bits 01 ( or ’h’ ) means high, 00 means medium, and 11 ( or ’l’ ) means low. Bits 10 is reserved, and must not be specified. There is no character to specify the medium preference explicitly. The default value of the entire flag is 0 ( or a null string, ) which means no additional configuration methods, and the medium router preference.
rltime
(num) Router lifetime field (unit: seconds). The value must be either zero or between the value of maxinterval and 9000. When rtadvd runs on a host, this value must explicitly set 0 on all the advertising interfaces as described in rtadvd(8). The default value is 1800.
rtime
(num) Reachable time field (unit: milliseconds). The default value is 0, which means unspecified by this router.
retrans
(num) Retrans Timer field (unit: milliseconds). The default value is 0, which means unspecified by this router.
The following items are for ICMPv6 prefix information option, which will be attached to router advertisement header. These items can be omitted, then rtadvd will automatically get appropriate prefixes from the kernel’s routing table, and advertise the prefixes with the default parameters. Keywords other than clockskew can be augmented with a number, like "prefix2", to specify multiple prefixes.
clockskew
(num) Time skew to adjust link propagation delays and clock skews between routers on the link (unit: seconds). This value is used in consistency check for locally-configured and advertised prefix lifetimes, and has its meaning when the local router configures a prefix on the link with a lifetime that decrements in real time. If the value is 0, it means the consistency check will be skipped for such prefixes. The default value is 0.
prefixlen
(num) Prefix length field. The default value is 64.
pinfoflags
(str or num) A 8-bit flags field in prefix information option. This field can be specified either as a case-sensitive string or as an integer. A sting consists of characters each of which corresponds to a particular flag bit(s). An integer should be the logical OR of all enabled bits. Bit 7 ( ’l’ or 0x80 ) means On-link flag bit, and Bit 6 ( ’a’ or 0x40 ) means Autonomous address-configuration flag bit. The default value is "la" or 0xc0, i.e., both bits are set.
addr
(str) The address filled into Prefix field. Since ":" is used for termcap(5) file format as well as IPv6 numeric address, the field MUST be quoted by doublequote character.
vltime
(num) Valid lifetime field (unit: seconds). The default value is 2592000 (30 days).
vltimedecr
(bool) This item means the advertised valid lifetime will decrement in real time, which is disabled by default.
pltime
(num) Preferred lifetime field (unit: seconds). The default value is 604800 (7 days).
pltimedecr
(bool) This item means the advertised preferred lifetime will decrement in real time, which is disabled by default.
The following item is for ICMPv6 MTU option, which will be attached to router advertisement header. This item can be omitted, then rtadvd will use the default value.
mtu
(num or str) MTU (maximum transmission unit) field. If 0 is specified, it means that the option will not be included. The default value is 0. If the special string "auto" is specified for this item, MTU option will be included and its value will be set to the interface MTU automatically.
The following item controls ICMPv6 source link-layer address option, which will be attached to router advertisement header. As noted above, you can just omit the item, then rtadvd will use the default value.
nolladdr
(bool) By default ( if nolladdr is not specified ), rtadvd(8) will try to get link-layer address for the interface from the kernel, and attach that in source link-layer address option. If this capability exists, rtadvd(8) will not attach source link-layer address option to router advertisement packets.
The following item controls ICMPv6 home agent information option, which was defined with mobile IPv6 support. It will be attached to router advertisement header just like other options do.
hapref
(num) Specifies home agent preference. If set to non-zero, hatime must be present as well.
hatime
(num) Specifies home agent lifetime.
When mobile IPv6 support is turned on for rtadvd(8), advertisement interval option will be attached to router advertisement packet, by configuring maxinterval explicitly.
The following items are for ICMPv6 route information option, which will be attached to router advertisement header. These items are optional. Each items can be augmented with number, like "rtplen2", to specify multiple routes.
rtprefix
(str) The prefix filled into the Prefix field of route information option. Since ":" is used for termcap(5) file format as well as IPv6 numeric address, the field MUST be quoted by doublequote character.
rtplen
(num) Prefix length field in route information option. The default value is 64.
rtflags
(str or num) A 8-bit flags field in route information option. Currently only the preference values are defined. The notation is same as that of the raflags field. Bit 4 ( 0x10 ) and Bit 3 ( 0x08 ) are used to encode the route preference for the route. The default value is 0x00, i.e., medium preference.
rtltime
(num) route lifetime field in route information option. (unit: seconds). Since the specification does not define the default value of this item, the value for this item should be specified by hand. However, rtadvd allows this item to be unspecified, and uses the router lifetime as the default value in such a case, just for compatibility with an old version of the program.
In the above list, each keyword beginning with "rt" could be replaced with the one beginning with "rtr" for backward compatibility reason. For example, rtrplen is accepted instead of rtplen. However, keywords that start with "rtr" have basically been obsoleted, and should not be used any more.
You can also refer one line from another by using tc capability. See termcap(5) for details on the capability.
